Back to Blog
Tips & Care 2026-11-13 Products for bench top machinists | LittleMachineShop.com 0 views

0-685E V-Belt for 13" Drill Press: Wear Signs and Swap

0-685E V-Belt for 13" Drill Press: Wear Signs and Swap

Learn how to spot wear on your 13" drill press V-belt, check tension, and swap in the 0-685E replacement for model 5540 without guesswork.

Why the 0-685E Belt Deserves a Second Look

If your 13" drill press model 5540 is slipping, squealing, or losing speed under load, the V-belt is a sensible first suspect. The 0-685E V-belt is the replacement part that corresponds to drawing number 88 in the drill press documentation, so it is the correct belt for that specific model. Before you order, confirm your drill press is the 13" model 5540—this belt is not a universal fit.

This guide walks through the wear signs that justify a swap, a practical tension check, and the replacement steps. It sticks to what the supplied product information confirms and flags where you should consult your own machine's documentation.

Wear Signs That Point to a New Belt

  • Visible cracking or glazing: Inspect the belt's sides and inner circumference. Cracks, shiny glazed patches, or frayed edges mean the belt is no longer gripping as it should.
  • Slipping under load: If the spindle slows or stalls during drilling while the motor keeps running, the belt may be slipping. Check tension first, but persistent slipping after tensioning often means replacement.
  • Squealing or chirping: A slipping V-belt often makes a high-pitched noise, especially at startup or when drilling harder materials.
  • Stretched or loose fit: A belt that sits deep in the pulley groove or feels loose even after adjustment has likely stretched beyond useful service.

A Simple Tension Check Before You Replace

Before ordering a new belt, check tension on the existing one. With the drill press unplugged, press on the belt midway between the pulleys. It should feel firm with only slight deflection—if it feels mushy or bottoms out in the groove, tighten according to your drill press manual. The 0-685E listing does not supply a specific tension value or deflection measurement, so rely on your model 5540 documentation for the manufacturer's setting. If tension is correct and the belt still slips, replacement is the next step.

What the 0-685E Belt Fits

  • V-Belt, 0-685E, 13" Drill Press: Replacement V-belt for 13" Drill Press model 5540; corresponds to drawing number 88. Confirms this is the correct belt for your model 5540 and gives you a reference point in the documentation.
    V-Belt, 0-685E, 13" Drill Press
    V-Belt, 0-685E, 13" Drill Press

Swapping the Belt: Step by Step

These steps assume you have confirmed your drill press is the 13" model 5540 and have the new 0-685E belt on hand. Always unplug the drill press before working on the belt.

  1. Unplug and open the belt guard: Remove the screw or fastener holding the pulley cover, then lift it clear to expose the belt and pulleys.
  2. Release tension: Loosen the motor mount bolts or tension adjustment so the belt can be walked off the pulleys. Consult your manual for the exact adjustment on model 5540.
  3. Remove the old belt: Slide the belt off the motor and spindle pulleys. Note its routing so the new belt goes on the same way.
  4. Install the 0-685E belt: Route the new belt over the pulleys in the same path as the old one, seating it fully in the grooves.
  5. Retension and test: Adjust tension per your manual, tighten the motor mount, and turn the spindle by hand to confirm smooth rotation before plugging in.

After the Swap: What to Watch

Run the drill press briefly without load. Listen for squealing and check that the belt runs centered on the pulleys. If the new belt still slips, recheck tension and pulley alignment—do not overtighten, as that can damage bearings. The 0-685E is a direct replacement for the model 5540, but if you have a different drill press, verify fit before ordering. Keep the old belt as a backup only if it is not cracked or glazed.

Related Articles

Customer Service
Home
Products
Cart
Profile