Start with the spindle, not the set
An R8 collet set only works if your mill has an R8 spindle taper. The set of seven R8 round collets from LittleMachineShop is made to fit spindles with an R8 taper, and the drawbar thread is 7/16"-20. Check your mill's spindle and drawbar thread before you order, because a collet that fits the taper but not the drawbar is still the wrong collet.
If your mill uses a different taper, such as Morse or 3MT, this set is not for you. The catalog does not list alternative tapers for this product, so match the R8 specification to your machine first.
What the seven collets cover
- Collet Set, R8, Set of 7: Sizes from 1/8" to 3/4" by 8ths, plus 3/16" (1/8", 3/16", 1/4", 3/8", 1/2", 5/8", 3/4"). These are the sizes you need for common end mills, so one set covers most bench mill work without hunting for individual collets.

Collet Set, R8, Set of 7 - Collet Set, R8, Set of 7: This set includes all the sizes required for common end mills. If your end mill shanks fall in this range, you can skip buying singles and keep one organized set on the shelf.
- Collet Set, R8, Set of 7: Collets are made from high-grade tool steel and are precision ground and hardened. Tool steel and hardening are the baseline for holding a cutter securely; precision grinding matters for runout.
R8 collet sizes explained
The set covers 1/8", 3/16", 1/4", 3/8", 1/2", 5/8", and 3/4". That range matches common end mill shank sizes, so you can hold a 1/8" cutter for fine work and step up to 3/4" for heavier cuts without changing to a different tool holder system.
Notice the jump from 1/4" to 3/8": there is no 5/16" collet in this set. If your work relies on 5/16" shank tooling, you will need to add that size separately. The catalog does not list a 5/16" collet in this set, so plan around the sizes actually included.
Installing R8 collets: a safe sequence
The supplied product information does not include a manufacturer installation procedure. The steps below are general shop practice for R8 collets, not a substitute for your mill's manual. Always follow the manufacturer's instructions for your machine.
- Clean the taper and collet: Wipe the spindle taper and the collet's tapered surface free of chips and oil. A speck of debris can show up as runout.
- Seat the collet in the spindle: Insert the collet into the R8 spindle taper. The slot in the collet should engage the spindle key so the collet does not spin.
- Thread the drawbar: Thread the 7/16"-20 drawbar into the collet from the top of the spindle. Hand-tighten first to make sure threads engage smoothly.
- Insert the cutter: Slide the end mill shank into the collet until it is fully engaged. Avoid bottoming the cutter against the collet's internal shoulder if your collet has one.
- Tighten the drawbar: Snug the drawbar with the correct wrench. Overtightening can distort the collet and damage the spindle; use the torque your mill manual specifies.
- Remove in reverse: Loosen the drawbar a turn or two, then tap the drawbar top lightly if needed to release the collet. Never pry a collet out with a tool that could damage the taper.
R8 collet runout tips
The catalog lists a maximum runout of 0.0007" (0.018 mm) for this set. That is a specification for the collet itself, not a guarantee of the finished cut. Runout at the cutter tip also depends on the spindle, the drawbar tension, and how clean the mating surfaces are.
To keep runout in check, clean the taper and collet before every install, seat the collet fully, and tighten the drawbar consistently. If you see unacceptable runout, check the collet for chips or burrs and confirm the spindle taper is clean before blaming the collet. The supplied information does not include a runout measurement procedure, so use the method your mill manual or dial indicator instructions provide.
Runout specification at a glance
- Collet Set, R8, Set of 7: Maximum runout is 0.0007" (0.018 mm). This is the collet's stated limit, useful as a benchmark when you check your own setup with a dial indicator.
When this R8 collet set fits your bench mill
- Your spindle is R8: The set is made for R8 taper spindles. Confirm the taper before ordering.
- Your drawbar is 7/16"-20: The collets have a 7/16"-20 drawbar thread. A different drawbar thread means these collets will not thread on.
- Your cutters use common shank sizes: The set covers 1/8" through 3/4" in the steps listed. If you mostly use 5/16" shanks, add that size separately.
- You want one organized set: Seven collets in a set keep common sizes together and reduce the chance of grabbing the wrong holder.
Where the catalog stops
The supplied information does not include a manufacturer installation guide, torque values, or a runout checking procedure for this set. It also does not list a 5/16" collet. Treat those gaps as questions for your mill manual or the store's technical support rather than assuming a specification.
For most bench mill users with an R8 spindle and 7/16"-20 drawbar, the set of seven covers the everyday end mill sizes. Check the taper and thread first, keep the collets clean, and tighten consistently to get the most from the set.


