Two 2MT tools, two different jobs
A 2 Morse taper spindle can accept both collets and a drill chuck arbor, but they solve different problems. Collets grip the shank of a cutting tool directly. A drill chuck arbor adapts the spindle to a drill chuck, which then holds drill bits. The right choice depends on what you need to hold and whether the interface matches your spindle and tooling.
This comparison uses only the supplied catalog details for the 2 Morse taper collets and the 2MT drill chuck arbor. Where the catalog does not state a dimension or compatibility, treat that as a check to make on your machine rather than an assumption.
What the 2 Morse taper collets are built to hold
- Collets, 2 Morse Taper, Individual Sizes: #2 Morse taper collets fit spindles with a Morse taper and are made from high-grade tool steel, precision ground and hardened. This is a direct spindle interface, so the collet seats in the taper and grips a cutting tool shank without an intermediate chuck.

Collets, 2 Morse Taper, Individual Sizes - Collets, 2 Morse Taper, Individual Sizes: The drawbar thread is 3/8"-16 and the overall length is 2.67" (68 mm). The drawbar thread tells you what retaining hardware the collet expects; the length helps you judge whether it suits your spindle depth.
- Collets, 2 Morse Taper, Individual Sizes: Available sizes are 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", and 1/2". You match the collet size to the shank diameter of the tool you intend to hold, so measure the shank before ordering.
What the 2MT drill chuck arbor adapts
- Arbor, Drill Chuck 2MT Tang to 3/8"-24 Thread: The arbor is a 2 Morse taper to 3/8"-24 thread with a tang end. The 3/8"-24 thread is the chuck side of the interface, so this arbor is for mounting a chuck with that thread, not for holding a tool shank directly.

Arbor, Drill Chuck 2MT Tang to 3/8"-24 Thread - Arbor, Drill Chuck 2MT Tang to 3/8"-24 Thread: The tail end of the arbor should be cut off for full insertion into the mini lathe tailstock. This is a supplied instruction for a specific use. If you plan to use the arbor in a mini lathe tailstock, plan for that modification; if you plan to use it in a mill spindle, confirm whether the tang suits your setup.
Collet vs drill chuck arbor: the practical differences
- Tool holding method: Collets grip the tool shank directly in the 2MT taper. The arbor adapts the 2MT spindle to a 3/8"-24 threaded drill chuck, and the chuck then holds the bit.
- Typical work: Use collets when you need to hold a shank of a matching size, such as an end mill or other tool with a 1/8" to 1/2" shank. Use the arbor when you need a drill chuck on a 2MT spindle.
- Retention and interface: The collet uses a 3/8"-16 drawbar thread. The arbor uses a 3/8"-24 chuck thread. These are different threads and are not interchangeable.
- Modification note: The arbor has a tang, and the catalog states the tail end should be cut off for full insertion into the mini lathe tailstock. The collet listing does not include a comparable modification instruction.
- What the catalog does not state: The supplied details do not give runout figures, maximum tool shank capacity beyond the listed collet sizes, or a complete list of machines each item fits. Confirm those points against your machine and tooling before ordering.
How to choose between them
Start with the tool you need to turn. If it has a cylindrical shank that matches one of the collet sizes and you want to hold it directly in the 2MT spindle, the collet is the simpler interface. If you need to hold drill bits of varying sizes, a drill chuck is the usual approach, and the 2MT arbor is the adapter that mounts that chuck on a 2MT spindle.
Then check the threads. The collet calls for a 3/8"-16 drawbar thread; the arbor presents a 3/8"-24 thread for the chuck. Mixing those up will not give you a working setup. Also confirm whether your spindle is a 2MT spindle, since both items are built around that taper.
Finally, account for the arbor's tang and the supplied note about cutting off the tail end for mini lathe tailstock use. If you are not using a mini lathe tailstock, that instruction may not apply, but the tang still affects how the arbor seats in your spindle. The catalog does not spell out every machine-specific fit, so dry-fit and check before committing to a cut.
Checks before you order
- Measure the tool shank: Compare it to the collet sizes: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", or 1/2". A collet only grips its matching size.
- Identify your chuck thread: The arbor is 3/8"-24 on the chuck side. Confirm your drill chuck uses that thread before ordering.
- Check your drawbar: The collet's drawbar thread is 3/8"-16. Make sure your drawbar matches if you intend to retain the collet that way.
- Confirm the spindle taper: Both items are 2 Morse taper. Do not assume a different taper will fit.
- Plan for the arbor tang: The arbor has a tang, and the catalog instructs cutting off the tail end for full insertion into the mini lathe tailstock. Decide whether that applies to your use before modifying the part.



