What fine diamond knurls produce
Fine diamond knurls cut a diamond-shaped pattern with a fine pitch. The pair from LittleMachineShop.com creates 33 lines per inch, which is a noticeably finer texture than coarse knurls. That finer pitch suits small-diameter work and handles where a less aggressive grip is acceptable.
The pattern comes from two wheels that press into the workpiece together. One wheel carries a left-hand angle and the other a right-hand angle; running them in the same pass forms the diamond. The pitch you see is set by the wheels, not by lathe speed or feed.
Because these are fine-pitch wheels, they remove less material per pass than a coarse knurl. That can make them easier to control on a bench lathe, but it also means the finished grip is subtler. Decide which texture you want before you buy.
Wheel dimensions that affect your setup
- Knurls, Fine Diamond: This is a pair of fine diamond high speed steel knurls. You get both wheels needed for a diamond pattern in one purchase, and high speed steel is the expected material for knurl wheels.

Knurls, Fine Diamond - Knurls, Fine Diamond: These knurls are 3/4" diameter, 3/8" wide and have a 1/4" shaft hole. The 1/4" hole must match the pins or shaft of your knurling tool. The 3/4" diameter and 3/8" width also affect clearance around the work.
- Knurls, Fine Diamond: They create 33 lines per inch. This is the fine pitch that defines the texture. Compare it with any coarse knurl you already own before choosing this pair for a job.
Checkpoints before you mount the wheels
The catalog record for these knurls does not include a full setup or operating procedure. The checks below are general workshop practice, not manufacturer instructions. Use your lathe and knurling tool documentation for the actual procedure.
- Match the shaft hole: Confirm that the pins or axle on your knurling tool are 1/4" so the wheels seat correctly. A loose or forced fit will affect the pattern.
- Check wheel clearance: Each wheel is 3/4" in diameter and 3/8" wide. Make sure the tool and work area give the wheels room to contact the workpiece without rubbing the carriage or chuck.
- Confirm the pitch suits the part: At 33 lines per inch, the diamond is fine. On a very small diameter the pattern may look dense; on a large surface it may read as subtle. Judge against your drawing or sample.
- Inspect the wheels: Look for chips or wear on the teeth before installing. A damaged wheel will transfer that damage into the workpiece.
A practical order for diamond knurling on a bench lathe
The supplied product record does not specify speeds, feeds, or pressure settings for these knurls. The sequence below covers the mechanical setup only; set running parameters according to your lathe and tooling guidance.
- Mount the pair on the tool: Fit both wheels to the knurling tool with the 1/4" shaft hole aligned on the pins. One wheel should angle left and the other right so they form a diamond.
- Set the tool height: Bring the knurling tool to center height on the work, following your lathe or tool instructions.
- Position the work: Set the workpiece in the lathe and choose a starting point that lets the full 3/8" wheel width contact the surface you intend to knurl.
- Engage the wheels: Bring the wheels into contact with the work and apply the pressure your setup requires. The fine 33-lines-per-inch pattern will begin to form as the work rotates.
- Inspect and adjust: Stop and check the pattern depth and uniformity. Fine knurls can require more than one pass to reach the desired texture; judge by the result, not by a fixed number of passes.
Where the catalog stops and your machine takes over
The record for these fine diamond knurls gives the wheel dimensions, hole size, material and pitch. It does not include a manufacturer procedure, recommended speeds, or maximum pressure. That means the operating settings are your responsibility, based on your lathe, your knurling tool, and the material you are knurling.
If you need a documented procedure for a specific machine, consult the lathe and tooling documentation rather than treating this article as a substitute. The value here is in matching the wheels to your tool and understanding what the 33-lines-per-inch pitch will look like before you commit to a setup.


