Start with the screw you actually have
An M4x6 pan head Phillips machine screw is a small metric fastener with a pan-shaped head and a cross recess. On bench top machines it is the kind of screw that holds covers, brackets, and light panels in place. The catalog listing for this screw identifies it as an M4 x 6 metric machine screw with a pan head, Phillips drive, and black finish, brand McMaster-Carr, SKU 3873.
Before you install a replacement, confirm the thread size and length against the screw you are removing. The M4 designation refers to the metric thread size, and the 6 refers to the screw length as listed by the supplier. The catalog does not provide a thread pitch, head diameter, or drive size, so check those details against your old screw or the tapped hole before ordering.
Catalog details for this M4x6 screw
- Screw, M4x6 Pan Head Phillips Machine: Metric machine screw, M4 x 6, pan head with Phillips drive, black finish. These are the identifying features to match when replacing a missing or damaged screw.

Screw, M4x6 Pan Head Phillips Machine - Screw, M4x6 Pan Head Phillips Machine: Brand: McMaster-Carr; SKU: 3873. Use the brand and SKU to confirm you are ordering the same fastener style.
A practical installation sequence
The catalog does not include manufacturer torque values or a specific installation procedure for this screw, so use the steps below as general good practice for small machine screws. Always follow any machine-specific instructions that came with your bench mill or lathe.
- Match the screw to the hole: Compare the M4x6 screw with the original. The thread should engage smoothly by hand for the first few turns. If it binds immediately, stop and check the thread size and pitch.
- Check the Phillips drive: Use a Phillips driver that fits the recess snugly. A worn or undersized tip can cam out and damage the screw head, especially on a small pan head screw.
- Start the thread by hand: Turn the screw in by hand until it seats. This helps you feel cross-threading early, before you apply any force with a driver.
- Tighten in small increments: Snug the screw with the driver, then stop. The catalog does not supply a torque specification, so avoid guessing a high value. For a small M4 screw in a machine panel, firm seating is usually enough; over-tightening can strip threads or crush a thin panel.
- Recheck after use: After the machine has run, check that the screw is still snug. Vibration can loosen small fasteners over time.
Where this screw type commonly appears
The catalog lists this screw under fasteners and screws for bench top machinist use, but it does not name specific machine models or assemblies. Use the following as general examples of pan head machine screw uses, then confirm fit on your own machine.
- Control box and electrical covers: Pan head screws are often used where a low-profile head is wanted and the screw head will be visible. Check that the screw length is correct for the cover thickness.
- Brackets and small panels: An M4 machine screw can secure light brackets or panels. Make sure the screw does not protrude into a moving part or wiring.
- Replacing a lost or damaged screw: If you are replacing a screw, match the original head style and length. A pan head Phillips screw is a common replacement when the original had the same drive and head shape.
Torque and tightness: what the catalog does not tell you
The supplied product record does not include a torque specification, tensile strength, or recommended tightening value for this screw. That means you should not rely on a generic torque chart without confirming it applies to this exact fastener and the material it threads into. For small machine screws, the safest approach is to tighten by feel: bring the screw to contact, then snug it without forcing. If the screw is holding a plastic or thin metal cover, use even less force.
If a screw keeps loosening, first check whether the thread is damaged or the hole is worn. A thread-locking compound may help, but follow the compound manufacturer's instructions and make sure it is compatible with your machine. The catalog does not provide guidance on thread lockers for this screw.
When to replace rather than reuse
A small machine screw is inexpensive, but replacing the wrong one can cause more work than it saves. Use these checks to decide whether the M4x6 screw in your hand is still serviceable.
- Damaged Phillips recess: If the cross recess is rounded or burred, the driver may slip. Replace the screw rather than risk damaging the head further.
- Corroded or stripped threads: Black finish screws can still corrode in a damp shop. If the threads are rough or flattened, a new screw is the safer choice.
- Wrong length or head style: If the original screw sat flush or below the surface, a pan head may stand proud. Check clearance before installing.
A note on fit and compatibility
The catalog record for this screw does not list machine compatibility, so it cannot confirm that this exact screw fits a particular bench mill or lathe model. The safest method is to compare it with the screw you are replacing: same thread size, same length, same head shape, and a drive that matches your driver. If you are unsure, measure the old screw with calipers and check the thread against a known M4 nut or gauge. The catalog price is listed at USD 0.37, with a comparison price of USD 0.59, but confirm current pricing and availability before ordering.


